Craftsman Evolv Brad Nailer 6G28/F50 Manual

The Craftsman Evolv Brad Nailer 6G28/F50 is a pneumatic 18-gauge brad nailer designed for precision trim, molding, and finish work. It features a lightweight composite body, adjustable depth drive, tool-free jam release, no-mar tip, and accepts 5/8" to 2" brad nails. Below are key sections for safety, features, operation, maintenance, troubleshooting, and specifications.

1. Features at a Glance 2. Safety Information 3. Parts Identification 4. Specifications 5. Setup & Operation 6. Loading Nails 7. Depth Adjustment 8. Maintenance & Cleaning 9. Troubleshooting 10. Warranty Information

Features at a Glance

Key components: Lightweight composite body, adjustable exhaust, depth adjustment wheel, tool-free jam release, no-mar tip, magazine release latch, safety contact tip.

Feature	Description
Gauge	18-gauge brad nails
Nail Length Range	5/8" to 2" (16mm to 50mm)
Magazine Capacity	Up to 100 nails
Operating Pressure	70-120 PSI
Air Inlet	1/4" NPT
Depth Adjustment	Tool-free dial for flush or countersink
Jam Release	Tool-free clearing mechanism
No-Mar Tip	Prevents surface damage
Exhaust Direction	Adjustable to divert air away from user
Weight	2.6 lbs (1.2 kg)

Safety Information

Read all instructions before use. Wear safety glasses and hearing protection.

Disconnect air supply before loading, clearing jams, or performing maintenance.
Keep hands and body away from the nail exit area.
Do not point the tool at yourself or others.
Use only compressed air; do not use oxygen, combustible gases, or bottled gases.
Ensure workpiece is free of nails, screws, or obstructions before nailing.

WARNING! Risk of serious injury. Always follow safety procedures. Do not modify tool.

Parts Identification

Front: No-mar tip, safety contact tip. Top: Depth adjustment wheel, exhaust port. Rear: Air inlet. Side: Magazine release latch, magazine. Bottom: Trigger, handle.

Specifications

Model: Craftsman Evolv 6G28/F50
Type: Pneumatic Brad Nailer
Nail Gauge: 18-gauge
Nail Length: 5/8" to 2" (16-50mm)
Magazine Capacity: 100 nails
Operating Pressure: 70-120 PSI
Air Consumption: 0.3 CFM per shot
Air Inlet: 1/4" NPT
Tool Weight: 2.6 lbs (1.2 kg)
Sound Pressure: < 90 dB(A)
Vibration: < 2.5 m/s²

Setup & Operation

Connect to air compressor with 1/4" air hose. Adjust compressor regulator to 70-120 PSI.

Connect air hose to tool's air inlet.
Set compressor pressure within recommended range.
Load nails into magazine (see Loading Nails section).
Adjust depth setting as needed.
Place safety tip against workpiece, depress to enable firing.
Squeeze trigger to drive nail.

CAUTION! Always wear eye protection. Ensure workpiece is securely supported.

Loading Nails

Use only 18-gauge brad nails within specified length range.

Disconnect air supply.
Press magazine release latch and open magazine.
Insert nail strip with nails pointing down toward nosepiece.
Close magazine until it clicks locked.
Reconnect air supply.

Tip: Keep nails clean and dry for optimal performance.

Depth Adjustment

Adjust nail depth for flush or countersink applications.

Rotate depth adjustment wheel: "+" for deeper drive, "-" for shallower drive.
Test on scrap material to verify setting.
Fine-tune as needed for different materials.

Note: Proper adjustment prevents surface damage and ensures holding power.

Maintenance & Cleaning

Disconnect air supply before maintenance. Clean tool regularly.

Wipe exterior with clean, dry cloth.
Add 2-3 drops of pneumatic tool oil into air inlet daily before use.
Inspect O-rings and seals for wear; replace if damaged.
Keep magazine clean and free of debris.

CAUTION! Use only recommended pneumatic tool oil. Do not over-lubricate.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Tool does not fire	Low air pressure, safety tip not depressed	Check compressor PSI; ensure tip is fully pressed against workpiece.
Nails not driving flush	Incorrect depth setting	Adjust depth wheel; test on scrap material.
Nail jam	Damaged nails, debris in magazine	Disconnect air; use tool-free jam release to clear. Reload with clean nails.
Air leakage	Loose connections, damaged O-ring	Tighten air hose; inspect and replace O-ring if needed.
Weak driving force	Low air pressure, worn driver blade	Increase PSI within range; inspect driver blade for wear.

Service: For repairs, contact authorized Craftsman service center.

Warranty Information

Craftsman Evolv Brad Nailer 6G28/F50 comes with a limited warranty. For warranty claims, contact Craftsman Customer Service at 1-888-331-4569 or visit www.craftsman.com. Keep original receipt as proof of purchase.