The Banks 16 Gauge Finish Nailer is a pneumatic tool designed for precision finish work, such as installing trim, crown molding, baseboards, and cabinetry. It drives 16-gauge finish nails ranging from 1" to 2-1/2" in length. Features include a lightweight magnesium body, adjustable depth-of-drive, tool-free jam release, 360-degree adjustable exhaust, and a no-mar tip. Below are key sections for safety, features, operation, maintenance, and troubleshooting.
Key components: Magnesium body, adjustable depth-of-drive wheel, quick-clear jam release, 360-degree exhaust port, no-mar tip, safety contact tip.
| Feature | Description |
|---|---|
| Nail Gauge & Length | 16-gauge finish nails, 1" to 2-1/2" |
| Operating Pressure | 70-120 PSI (recommended 80-100 PSI) |
| Magazine Capacity | Up to 100 nails |
| Depth-of-Drive | Tool-free adjustable wheel |
| Jam Release | Tool-free mechanism for quick clearing |
| Exhaust Port | 360-degree adjustable to direct air away |
| Weight | Approximately 3.5 lbs |
| Safety Mechanism | Sequential contact trip for safe operation |
| No-Mar Tip | Prevents damage to workpiece surface |
| Air Inlet | 1/4" NPT with swivel connector |
Read all instructions before use. Always wear safety glasses and hearing protection.
WARNING! Do not depress the safety contact tip and trigger unless nailer is firmly pressed against workpiece. Serious injury may occur.
Front: No-mar tip, safety contact tip. Top: Depth-of-drive adjustment wheel. Side: Magazine release latch, exhaust port. Rear: Air inlet, trigger. Bottom: Jam release lever.
Remote: Not applicable; tool is pneumatic.
Controls: Trigger, safety contact tip, depth adjustment wheel, magazine latch, exhaust port dial, jam release lever.
Connect to air compressor with 1/4" hose. Adjust compressor regulator to 80-100 PSI.
Tip: Always use an in-line filter/regulator to remove moisture and debris from air line.
Use only 16-gauge angled finish nail strips compatible with this tool.
WARNING! Never load nails with air connected. Keep fingers clear of magazine during closing.
Depth-of-Drive: Turn wheel clockwise to drive nails deeper; counterclockwise for shallower depth. Test on scrap wood.
Exhaust Direction: Rotate exhaust port dial to direct air away from user and workpiece.
No-Mar Tip: Replace if worn or damaged to prevent surface marks.
Disconnect air before maintenance. Daily: Add 3-5 drops pneumatic oil into air inlet. Weekly: Clean exterior with dry cloth; inspect O-rings and seals. Monthly: Lubricate moving parts with light oil.
CAUTION! Use only recommended lubricants. Do not disassemble beyond user-serviceable parts.
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| Nailer does not fire | Low air pressure, safety tip not engaged | Check PSI (80-100); press tip firmly to workpiece. |
| Nails not driving flush | Depth setting incorrect, worn driver blade | Adjust depth wheel; inspect/replace driver blade. |
| Nails jamming | Wrong nail size, dirty magazine, dry tool | Use correct nails; clean magazine; lubricate tool. |
| Air leakage | Loose fittings, damaged O-rings | Tighten connections; replace O-rings. |
| Weak driving force | Low air pressure, internal wear | Increase PSI; check piston seals for wear. |
Reset: Clear all jams; lubricate; ensure proper air supply.
Service: For repairs, contact authorized Banks service center.
Banks 16 Gauge Finish Nailer comes with a 1-year limited warranty covering defects in materials and workmanship. Warranty does not cover misuse, lack of maintenance, or normal wear. Proof of purchase required. For warranty claims, visit www.bankstools.com or call 1-800-555-TOOL.